Renesas SuperH SH7343 Technical Information PDF herunterladen (Seite 47)

Target interface (SH7211F) Jun. 1, 2010 (Second Edition)

Mictor connector

Signals

CPU Pin No. CPU Pin No.Pin

No.

Signal

Input/

Output

LQFP-144

No.

Signal

Input/

Output

LQFP-144

1 N.C. 2 N.C.

3 GND (ASEMD)

(Input) (29) 4 N.C.

5 GND (CON)

(Output) 6 AUDCK Output 110

7 N.C. 8

ASEBRKAK

ASEBRK

Input/Output

9 RES Output 22 10 N.C.

11 TDO Output 15 12 VCC_AUD

Output

13 N.C. 14 VCC

Output

15 TCK Input 16 16 N.C.

17 TMS Input 17 18 N.C.

19 TDI Input 12 20 N.C.

21 TRST Input 18 22 N.C.

23 N.C. 24 AUDATA3 Output 111

25 N.C. 26 AUDATA2 Output 112

27 N.C. 28 AUDATA1 Output 115

29 N.C. 30 AUDATA0 Output 116

31 N.C. 32 AUDSYNC Output 109

33 N.C. 34 N.C.

35 N.C. 36 N.C.

37 N.C. 38 N.C.

・ For the pin where stated as N.C. in the table, leave the signal unconnected.

*1: Input/output is based on the target system.

*2: To debug,

ASEMD pin needs to be brought to Low state.

Shown in the target connection reference diagram is the circuit that brings ASEMD pin to Low state when you connect ASEMD signal to the connector for

debugger. If you do not connect ASEMD signal to Pin No. 3 of the connector for debugger, the circuit that sets ASEMD pin by switch circuit will do. However, in

such case, do not connect ASEMD pin to Pin No. 3 of the connector for debugger, but connect Pin No. 3 of connector for the debugger to GND.

*3: For VCC_AUD, the power same as the voltage level at which AUD signal of CPU works is to be connected. Connect the AUD signal to I/O

power of CPU.

*4: For VCC, the power same as the voltage level at which HUDI signal of CPU works is to be connected. Connect the HUDI signal to I/O power

of CPU.

*5: By detection of GND on the target system side, whether the target system is connected or not is determined.

Target connection reference diagram

Mictor connector specifications

Recommended connector

Manufacturer AMP

Model Mictor connector

2-767004-2 / 767054-1 / 767061

(Top view on the target board)

(For detailed dimensions of the connector,

refer to the documentation by manufacturer of the connector.)

*Please look at the pin configuration diagram above and make

sure that the connector is in the right direction before connecting.

Please check the pin number in the signal table above and make sure

the signal and the pin numbers match.

*1:

RES, which is connected to Pin No. 9 of the connector for debugger, is the signal that debugger uses for monitoring the state of RES pin of

CPU.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 203 204

Kommentare zu diesen Handbüchern

Keine Kommentare

Renesas SuperH SH7343 Technical Information Seite 47

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Renesas SuperH SH7343