Renesas SuperH SH7343 Technical Information Seite 38
- Seite / 204
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Target interface (SH7616) Jun. 30, 2009 (Second Edition)
■ SH7616
Applicable products PALMiCE3-SH / PALMiCE2-SH
Applicable connector
(Connector for debugger)
MIL connector (14-pin design)
MIL connector
Signals
CPU Pin No. CPU Pin No. Pin
No.
Signal
Input/
Output
*1
PLQP0208KA-A
Pin
No.
Signal
Input/
Output
*1
PLQP0208KA-A
1 TCK Input 30 2 N.C.
3 TRST Input 32 4 GND(ASEMODE)
*2
(Input) (6)
5 TDO Output 28 6 GND
7 N.C. 8 VCC
*3
Output
9 TMS Input 31 10 GND
11 TDI Input 29 12 GND
13 RES Output 8 14 GND
・ For the pin where stated as N.C. in the table, leave the signal unconnected.
*1: Input/output is based on the target system.
*2: To debug, ASEMODE pin needs to be brought to Low state.
Shown in the target connection reference diagram is the circuit that brings ASEMODE pin to Low state when you connect ASEMODE signal to the connector for
debugger.
If you do not connect ASEMODE signal to Pin No. 4 of the connector for debugger, the circuit that sets ASEMODE pin by switch circuit will do. However, in such
case, do not connect ASEMODE pin to Pin No. 4 of the connector for debugger, but connect Pin No. 4 of connector for the debugger to GND.
*3: For VCC, connect I/O power of CPU. Debugging can be performed even if the signal is N.C., however, by connecting I/O power, leak during
the target system power OFF can be prevented.
Target connection reference diagram
MIL connector specifications
Recommended connector
Manufacturer Omron Corporation
Model XG4C-1431
(Top view on the target board)
(For detailed dimensions of the connector,
refer to the documentation by manufacturer of the connector.)
*Please look at the pin configuration diagram above and make
sure that the connector is in the right direction before connecting.
Please check the pin number in the signal table above and make sure
the signal and the pin numbers match.
*1:
RES, which is connected to Pin No. 13 of the connector for debugger, is the signal that debugger uses for monitoring the state of RES pin of
CPU.
- Technical Information 1
- Document change history 2
- AUD probe 5
- Mictor probe 5
- HUDI cable 5
- ■ SH7047F 7
- ■ SH7055F 10
- ■ SH7055SF 12
- ■ SH7058F 14
- ■ SH7058SF/SH7059F 16
- (SH7058SF/SH7059F) 17
- ■ SH7144F/SH7145F 21
- history (SH7144F/SH7145F) 23
- ■ SH7146F 24
- ■ SH7149F 26
- (SH7149F) 28
- ■ SH7606 29
- ■ SH7618/SH7618A 31
- Also, added CPU SH7618A 32
- ■ SH7619 33
- SH2-DSP 35
- ■ SH7615 36
- ■ SH7616 38
- ■ SH7206 41
- ■ SH7211F 45
- ■ SH7243F/SH7285F/ SH7286F 49
- (Output) 52
- (SH7243F/SH7285F/ SH7286F) 54
- SH2A-FPU 55
- ■ SH7201 56
- (SH7201) 59
- ■ SH7203 60
- ■ SH7261 64
- ■ SH7262/SH7264 68
- ■ SH7263 72
- SH2A-DUAL 78
- ■ SH7205 79
- ■ SH7265 83
- ■ SH7705 88
- ■ SH7706 91
- ■ SH7709S 94
- SH3-DSP 97
- ■ SH7290(SH-Mobile1) 98
- ■ SH7294(SH-MobileJ) 101
- (SH7294(SH-MobileJ)) 103
- ■ SH7300(SH-MobileV) 104
- ■ SH7710 107
- ■ SH7712 110
- ■ SH7713 113
- ■ SH7720/SH7721 116
- Also, added CPU SH7721 118
- ■ SH7727 119
- ■ SH7729 122
- ■ SH7729R 125
- SH4AL-DSP 128
- ■ SH7343(SH-Mobile3AS) 129
- (SH7343(SH-Mobile3AS)) 131
- ■ SH7354(SH-MobileL3V) 132
- ■ SH7722(SH-MobileR) 135
- (SH7722(SH-MobileR)) 137
- ■ SH7750R/SH7750S 139
- BGA-292 140
- ■ SH7751/SH7751R 141
- ■ SH7760 144
- ■ SH7723(SH-MobileR2) 148
- ■ SH7730 152
- ■ SH7763 156
- ■ SH7764 159
- ■ SH7770 163
- (SH7770) 164
- ■ SH7774 165
- (SH7774) 166
- ■ SH7780 167
- ■ SH7781 170
- ■ SH7785 172
- Second Edition Jun. 1, 2010 174
- ・ Mictor connector 174
- PALMiCE3 HUDI140 model 175
- Hardware Manual 175
- Table of Contents 177
- Chapter 1 Getting Started 178
- 1.1 Introduction 179
- Product Composition Contents 180
- 1.3 Connection structure 181
- Chapter 2 182
- HUDI140 model specifications 183
- 2.3.1 RSTOUT probe 184
- How revision sticker reads 185
- 3.1 Introduction 187
- 3.2 H-UDI interface 187
- 3.2.5 RSTOUT signal 188
- CM845(C)1101 189
- PALMiCE3 AUD360 model 190
- AUD360 model specifications 198
- 3.2 AUD interface 202
- 3.2.4 RSTOUT signal 203
- Aug. 2011 Fourth Edition 204
- CM884(D)1108 204
Verwandte Produkte und Handbücher für Vernetzung Renesas SuperH SH7343
Vernetzung Renesas M16C/6NN Bedienungsanleitung
(36 Seiten)
(36 Seiten)
Vernetzung Renesas TM V.3.20A Spezifikationen
(762 Seiten)
(762 Seiten)
Vernetzung Renesas M16C/6V Bedienungsanleitung
(18 Seiten)
(18 Seiten)
Vernetzung Renesas PC7501 Bedienungsanleitung
(46 Seiten)
(46 Seiten)
Vernetzung Renesas R8C/17 Betriebsanweisung
(97 Seiten)
(97 Seiten)
(18 Seiten)
Vernetzung Renesas R8C/Tiny Series Handbuch
(199 Seiten)
(199 Seiten)
Vernetzung Renesas M16C/30P Bedienungsanleitung
(29 Seiten)
(29 Seiten)
Vernetzung Renesas M16C FAMILY Handbuch
(11 Seiten)
(11 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern