Renesas M16C/6NK Technical Information Seite 113
- Seite / 412
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Rev.2.10 Apr 14, 2006 page 89 of 378
REJ09B0124-0210
M16C/6N Group (M16C/6NK, M16C/6NM) 10. Interrupts
10.5.4 Interrupt Sequence
An interrupt sequence — what are performed over a period from the instant an interrupt is accepted to the
instant the interrupt routine is executed — is described here.
If an interrupt request is generated while an instruction is being executing, the CPU determines its priority
when the execution of the instruction is completed, and transfers control to the interrupt sequence from
the next cycle. However, for the SMOVB, SMOVF, SSTR or RMPA instruction, if an interrupt request is
generated while the instruction is being executing, the MCU temporarily suspends the instruction being
executed, and transfers control to the interrupt sequence.
The CPU behavior during the interrupt sequence is described below.
Figure 10.5 shows the Time Required for Executing Interrupt Sequence.
(1) The CPU obtains interrupt information (interrupt number and interrupt request level) by reading
address 000000h. Then, the IR bit applicable to the interrupt information is set to 0 (interrupt
requested).
(2) The FLG register, prior to an interrupt sequence, is saved to a temporary register
(1)
within the CPU.
(3) Flags I, D, and U in the FLG register become as follows:
• The I flag is set to 0 (interrupt disabled)
• The D flag is set to 0 (single-step interrupt disabled)
• The U flag is set to 0 (ISP selected)
However, the U flag does not change state if an INT instruction for software interrupt Nos. 32 to 63 is
executed.
(4) The temporary register
(1)
within the CPU is saved to the stack.
(5) The PC is saved to the stack.
(6) The interrupt priority level of the acknowledged interrupt in IPL is set.
(7) The start address of the relevant interrupt routine set in the interrupt vector is stored in the PC.
After the interrupt sequence is completed, an instruction is executed from the starting address of the
interrupt routine.
NOTE:
1. This register cannot be accessed by user.
Figure 10.5 Time Required for Executing Interrupt Sequence
123456789 101112 13 14 15 16 17 18
SP-2
contents
SP-4
contents
vec
contents
vec+2
contents
Interrupt
information
Address
0000h
SP-2 SP-4 vec vec+2
PC
CPU clock
Address bus
Data bus
WR
(2)
RD
NOTES:
1. The undefined state depends on the instruction queue buffer.
A read cycle occurs when the instruction queue buffer is ready to accept instructions.
2. The WR signal timing shown here is for the case where the stack is located in the internal RAM.
Undefined
(1)
Undefined
(1)
Undefined
(1)
- To our customers 1
- Hardware Manual 3
- RENESAS MCU 3
- M16C FAMILY / M16C/60 SERIES 3
- Blank page 6
- How to Use This Manual 7
- 3. Register Notation 9
- Table of Contents 11
- __________ 12
- SFR Page Reference 17
- 1. Overview 25
- 1.2 Performance Overview 26
- 1.3 Block Diagram 28
- 1.4 Product Information 29
- 1.5 Pin Assignments 30
- M16C/6N Group 33
- (M16C/6NM) 33
- 1.6 Pin Functions 37
- 3. Memory 42
- 5. Resets 59
- 5.2 Software Reset 61
- 5.3 Watchdog Timer Reset 61
- 5.5 Internal Space 61
- 6. Processor Mode 62
- 6.2 Setting Processor Modes 63
- Processor Mode Register 0 64
- Processor Mode Register 1 65
- 7.1 Bus Mode 69
- 7.1.1 Separate Bus 69
- 7.1.2 Multiplexed Bus 69
- 7.2 Bus Control 70
- 7.2.2 Data Bus 70
- 7.2.3 Chip Select Signal 70
- 7.2.1 Address Bus 70
- 7.2.4 Read and Write Signals 72
- 7.2.5 ALE Signal 72
- 7.2.6 RDY Signal 73
- HOLD > DMAC > CPU 74
- 7.2.10 Software Wait 76
- 8. Clock Generation Circuit 80
- Figure 8.2 CM0 Register 82
- Figure 8.3 CM1 Register 83
- Figure 8.4 CM2 Register 84
- Figure 8.5 PCLKR Register 85
- CAN0/1 Clock Select Register 86
- PLL Control Register 0 87
- 8.1.1 Main Clock 88
- 8.1.2 Sub Clock 89
- 8.1.4 PLL Clock 90
- 8.2.1 CPU Clock and BCLK 92
- 8.3 Clock Output Function 92
- 8.4 Power Control 93
- 8.4.1 Normal Operating Mode 93
- 8.4.2 Wait Mode 95
- 8.4.3 Stop Mode 97
- REJ09B0124-0210 100
- State after Transition 101
- Current State 101
- 9. Protection 104
- 10.1 Type of Interrupts 105
- 10.2 Software Interrupts 106
- 10.2.2 Overflow Interrupt 106
- 10.2.3 BRK Interrupt 106
- 10.3 Hardware Interrupts 107
- 10.3.1 Special Interrupts 107
- 10.4.1 Fixed Vector Tables 108
- ________ 109
- 10.5 Interrupt Control 110
- Interrupt Control Register 111
- 10.5.1 I Flag 112
- 10.5.2 IR Bit 112
- 10.5.4 Interrupt Sequence 113
- _________ 114
- 10.5.7 Saving Registers 115
- 10.5.9 Interrupt Priority 116
- 10.6 INT Interrupt 118
- Figure 10.11 IFSR0 Register 119
- Figure 10.12 IFSR1 Register 120
- Figure 10.13 IFSR2 Register 121
- 10.7 NMI Interrupt 122
- 10.8 Key Input Interrupt 122
- 10.9 CAN0/1 Wake-up Interrupt 122
- 10.10 Address Match Interrupt 123
- 11. Watchdog Timer 125
- 12. DMAC 127
- ________ ________ 128
- Figure 12.2 DM0SL Register 129
- 12.1 Transfer Cycle 132
- 12.1.4 Effect of RDY Signal 132
- 12.2 DMA Transfer Cycles 134
- 12.3 DMA Enable 135
- 12.4 DMA Request 135
- 13. Timers 137
- 13.1 Timer A 139
- Up/Down Flag 141
- Count Start Flag 141
- One-Shot Start Flag 142
- Trigger Select Register 142
- Clock Prescaler Reset Flag 142
- 13.1.1 Timer Mode 143
- 13.1.2 Event Counter Mode 144
- 13.1.3 One-shot Timer Mode 149
- 13.2 Timer B 154
- 13.2.1 Timer Mode 157
- 13.2.2 Event Counter Mode 158
- Figure 13.20 160
- Figure 14.2 INVC0 Register 164
- Figure 14.3 INVC1 Register 165
- Dead Time Timer 166
- Timer B2 Register 167
- (1) (2) (3) 168
- Timer B2 Mode Register 170
- 15. Serial Interface 173
- _______ _______ 183
- _________ _________ 183
- Setting in UART Mode 191
- 15.1.3 Special Mode 1 (I 199
- Figure 15.23 I 200
- C Mode Block Diagram 200
- _______ ________ 201
- _______ ________ _______ 201
- Function 202
- 15.1.4 Special Mode 2 208
- Undefined 212
- (NOTE 2) 214
- (1) Transmit timing 217
- (2) Receive timing 217
- SIM card 218
- (1) Direct format 219
- (2) Inverse format 219
- 15.2 SI/Oi (i = 3 to 6) 220
- Bit Symbol 222
- 15.2.1 SI/Oi Operation Timing 224
- 15.2.2 CLK Polarity Selection 224
- 16. A/D Converter 226
- A/D Control Register 0 228
- A/D Control Register 1 228
- A/D Control Register 2 229
- A/D Register i (i = 0 to 7) 229
- 16.1 Mode Description 230
- 16.1.1 One-shot Mode 230
- 16.1.2 Repeat Mode 232
- 16.1.3 Single Sweep Mode 234
- 16.1.4 Repeat Sweep Mode 0 236
- 16.1.5 Repeat Sweep Mode 1 238
- 16.2 Function 240
- 16.2.2 Sample and Hold 240
- Data bus low-order 243
- D/A Control Register 244
- D/A Register i (i = 0, 1) 244
- 18. CRC Calculation 245
- Figure 18.3 CRC Calculation 246
- 19. CAN Module 247
- 19.1.3 CAN SFR Registers 248
- 19.4 CAN SFR Registers 252
- 19.5 Operational Modes 258
- Module idle 259
- Module transmits 259
- Module receives 259
- 19.5.5 Bus Off State 260
- CCLKR register 261
- CAN module 261
- 19.8 Bit-rate 262
- 19.11 Basic CAN Mode 265
- 19.14 Listen-Only Mode 266
- 19.15.1 Reception 268
- 19.15.2 Transmission 269
- 19.16 CAN Interrupt 270
- 20. Programmable I/O Ports 271
- 20.4 PCR Register 272
- Figure 20.1 I/O Ports (1) 273
- Figure 20.2 I/O Ports (2) 274
- Figure 20.3 I/O Ports (3) 275
- (inside dotted-line 276
- included) 276
- not included) 276
- Figure 20.5 I/O Ports (5) 277
- Figure 20.6 I/O Pins 277
- Port P8 Direction Register 278
- Port P8 Register 279
- Pull-up Control Register 0 280
- Pull-up Control Register 1 280
- Pull-up Control Register 2 280
- Port Control Register 281
- 21. Flash Memory Version 284
- 21.1 Memory Map 285
- 21.1.1 Boot Mode 286
- 21.2.2 ID Code Check Function 286
- Figure 21.2 ROMCP Register 287
- 21.3 CPU Rewrite Mode 288
- 21.3.1 EW0 Mode 289
- 21.3.2 EW1 Mode 289
- Power Dissipation Mode 294
- 21.3.5 Software Commands 297
- 21.3.6 Data Protect Function 302
- 21.3.8 Full Status Check 304
- 21.4 Standard Serial I/O Mode 306
- 21.4.1 ID Code Check Function 306
- Pin Name I/O 307
- Description 307
- M16C/6N Group (M16C/6NK) 308
- (Flash memory version) 308
- M16C/6N Group (M16C/6NM) 309
- 21.5 Parallel I/O Mode 311
- 21.6 CAN I/O Mode 312
- 21.6.1 ID Code Check Function 312
- _____________ 316
- (ripple) 318
- P-P(ripple) 318
- VCC = 5V 319
- Gain error 321
- Interrupt for 322
- (a) Stop mode release 322
- or 322
- (b) Wait mode release 322
- VCC = 5 V 323
- VCC = 3.3 V 337
- 23. Usage Notes 362
- 23.3 External Clock 364
- 23.5 Power Control 366
- A/D converter 367
- D/A converter 367
- 23.7 Protection 369
- 23.8 Interrupts 370
- 23.8.1 Reading Address 00000h 370
- 23.8.2 Setting SP 370
- 23.8.3 NMI Interrupt 370
- 23.8.5 INT Interrupt 371
- 23.9 DMAC 373
- 23.10 Timers 374
- 23.10.1 Timer A 374
- 23.10.2 Timer B 378
- 23.12 Serial Interface 381
- 23.12.2 Special Modes 382
- 23.12.3 SI/Oi (i = 3 to 6) 383
- 23.13 A/D Converter 384
- 23.14 CAN Module 386
- 23.15 Programmable I/O Ports 391
- 23.16 Dedicated Input Pin 392
- Version MCUs 393
- 23.19.10 Interrupts 396
- 23.19.11 How to Access 396
- 23.19.13 DMA Transfer 396
- 23.21 Noise 398
- Register Index 401
- REVISION HISTORY 403
- Rev.2.10 Apr 14, 2006 411
- Renesas Technology Corp 411
Verwandte Produkte und Handbücher für Vernetzung Renesas M16C/6NK
Vernetzung Renesas 740 Family Bedienungsanleitung
(195 Seiten)
(195 Seiten)
Vernetzung Renesas M16C/30P Bedienungsanleitung
(59 Seiten)
(59 Seiten)
Vernetzung Renesas H8S/2378F Bedienungsanleitung
(78 Seiten)
(78 Seiten)
Vernetzung Renesas M3062PT2-EPB Bedienungsanleitung
(104 Seiten)
(104 Seiten)
Vernetzung Renesas M16C/64 Datenblatt
(92 Seiten)
(92 Seiten)
Vernetzung Renesas 740 Family Bedienungsanleitung
(124 Seiten)
(124 Seiten)
Vernetzung Renesas H8S/2378F Technical Information
(109 Seiten)
(109 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern