Renesas H8S/2628 Technical Information Seite 390
- Seite / 430
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
362
8.1.7 Extended Monitor Function
Selecting [View -> CPU -> Extended Monitor] or clicking the [Extended Monitor] toolbar button displays the
[Extended Monitor] window. This emulator displays the following items.
Table 8.6 [Extended Monitor] Window Items
[Item] Column [Value] Column
User Standby Displays the status of the standby pin.
User NMI Displays the status of the NMI pin.
User Reset Displays the status of the reset pin.
User Wait Displays the status of the wait pin ("Inactive" is displayed if no corresponding
pins exist).
User System Voltage Displays whether or not the user VCC is equal to or exceeds the value set in
[User VCC Threshold] on the [General] page of the [Configuration Properties]
dialog box.
User System Voltage2 Displays whether or not the user VCC is supplied.
User Cable Displays whether or not the user cable is connected.
Running status Displays the address bus value in the MCU and the status of the CPU while
the user program is running, and the cause of a break while the user program
is halted.
Break = <Cause of break>: Displays the cause of a break.
Address = <Address bus value>:
Displays the address bus value during the user program execution. While in
subactive mode, ‘(SubActive)’ is displayed after the address bus value.
Status = <Status of the CPU>: Displays the status of the CPU.
PREFETCH: CPU instruction prefetch cycles
DATA: CPU data access cycles
DMAC: Operation of DMAC
DTC: Operation of DTC
SLEEP: Sleep mode
STANDBY: Standby mode
WATCH: Watch mode
SUBSLEEP: Subsleep mode
REFRESH: Refresh cycles
ROM Write Displays whether or not the ROM has been written to during the user program
execution.
Once the ROM has been written to, the state is retained until the Configure
Platform is set again.
Target Mode Displays the mode to be input from the user system.
Target Clock Displays whether or not there is a clock signal to be input from the user
system.
Target Sub Clock Displays whether or not there is a sub-clock signal to be input from the user
system. (However, ‘No Clock’ is always displayed here because the selection
of a sub-clock signal from the user system is not available with this emulator.)
Note: In this emulator, the update interval of the [Extended Monitor] window cannot be selected or changed.
- To our customers 1
- H8S/2628 E6000 3
- Cautions 5
- IMPORTANT INFORMATION 7
- LIMITED WARRANTY 8
- DISCLAIMER 8
- SAFETY PAGE 10
- CAUTION 12
- Introduction 13
- About This Manual 14
- Contents 15
- HEW Part 25
- 1. Overview 27
- 1.2 The Main Window 28
- 1.3 The Help System 35
- 1.4 Launching the HEW 36
- 1.5 Exiting the HEW 36
- 2. Build Basics 37
- 2.2 Project Files 38
- .SRC .ASM .MAR .C .LIB .LPF 44
- 2.5 Build Configurations 50
- 2.6 Building a Project 53
- 2.7 File Dependencies 56
- 3. Advanced Build Features 63
- 3.3 Ordering Build Phases 69
- 3.5 File Mappings 78
- 3.6 Controlling the Build 80
- 3.7 Logging Build Output 81
- 3.10 Generating a Makefile 84
- 4. Using the Editor 85
- 4.4 Editing a File 91
- 4.6 Bookmarks 96
- 4.7 Printing a File 96
- 4.8 Configuring Text Layout 97
- 4.9 Splitting a Window 100
- 4.10 Configuring Text 101
- 4.11 Syntax Coloring 102
- 4.12 Templates 104
- 5. Tools Administration 109
- 5.1 Tool Locations 110
- 5.3 Registering Components 111
- 5.4 Unregistering Components 112
- 5.8 Custom Project Types 118
- 6.1 Customizing the Toolbar 119
- 6.6 Customizing File Save 129
- 7. Version Control 133
- 8.3 Specifying Arguments 144
- 8.4 Controlling Execution 152
- 9. Using Visual SourceSafe 155
- Emulator Debugger Part 161
- Section 1 Overview 163
- 1.2 Warnings 164
- 1.3 Environmental Conditions 165
- 2.1 Emulator Preparation 167
- User system interface 168
- IC socket 168
- Emulator 169
- User system interface cable 169
- 2.4 Power Supply 170
- 2.5 SIMM Memory Module 170
- 2.6 Hardware Interface 171
- Trigger output 172
- 2.7 System Check 174
- Figure 2.17 HEW Window 177
- 2.8 Communication Problems 178
- 3.1 Debugging Features 179
- 3.3 Hardware Features 181
- 3.4 Stack Trace Function 182
- 3.5 Online Help 182
- 4.4 Debugger Sessions 196
- 4.6 Ending the Emulator 201
- Section 5 Debugging 203
- [General] page 204
- 5.2 Downloading a Program 209
- 5.4 Viewing the Registers 217
- 5.5 Operating Memory 219
- 5.6 Viewing the I/O Memory 227
- 5.10 Viewing the Labels 236
- 5.11 Executing Your Program 241
- 5.12 Stopping Your Program 245
- 5.13 Elf/Dwarf2 Support 247
- 5.14 Viewing the Variables 251
- 5.15 Using the Event Points 258
- 5.20 Analyzing Performance 315
- Section 6 Tutorial 327
- 6.2 Running the HEW 328
- 6.5 Setting Registers 332
- 6.6 Executing the Program 333
- 6.7 Reviewing Breakpoints 335
- 6.8 Referring to Symbols 336
- 6.9 Viewing Memory 337
- 6.10 Watching Variables 338
- 6.14 Resetting the MCU 346
- 6.15 Break Function 347
- 6.16 Trace Functions 353
- 6.17 Stack Trace Function 368
- 6.19 Monitor Function 372
- 6.20 What Next? 376
- 7.2 User System Interface 378
- Debugging Platform Remark 381
- [Custom Device] page 386
- [Custom Device] page (cont) 387
- 8.1.11 Trace Information 392
- Appendix A Troubleshooting 399
- Appendix C Placeholders 403
- C.3 Available Placeholders 405
- C.4 Placeholder Tips 407
- Appendix D I/O File Format 409
- Appendix F Menus 415
- Table F.1 GUI Menus (cont) 416
- Appendix G Command Lines 419
- Message Description 425
- H8S/2628 E6000 Emulator 430
- User’s Manual 430
Verwandte Produkte und Handbücher für Software Renesas H8S/2628
(26 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.100 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern