Renesas H8S/2168 Bedienungsanleitung

www.radisys.comPROMENTUM™ SHELF PERIPHERAL MODULEHARDWARE REFERENCE007-02656-0000 • December 2006ATCA-5000ATCA-5100

Product Description110Electrical componentsFigure 2. Block diagram of electrical components +12 V from hot-swap control +12 V+2.5 V+3.3 VIPMB-0 Displa

Face plate111Face plateFigure 3. Face plateEvent input connectorHot-swap LEDPIMOOS LEDPWR LEDApplication LEDTelco alarm connectorSerial port

Product Description112

13THEORY OF OPERATION2This chapter describes the main components of the SPM.IPMC subsystemThe Intelligent Platform Management Controller (IPMC) subsys

Theory of Operation214Hot-swap mechanismA hot swap switch on the bottom of the SPM is activated by the lower ejector latch. It can be used to request

Telco alarm interface215Telco alarm interfaceA telco alarm interface, as specified in the PICMG 3.0 Revision 2.0 AdvancedTCA Base Specification, is pr

Theory of Operation216The following diagram shows the suggested external connection to external equipment.Figure 4. Relay output connection—External c

Shelf interfaces217Figure 5. Reset input connection—External connection to external equipmentShelf interfacesThe following shelf I/Os are monitored by

Theory of Operation218IPMB interfaceThe SPM communicates with the rest of the system components through an Intelligent Platform Management Bus (IPMB-0

RTM function for front module219When not ‘active,’ the Renesas H8S/2168 microcontroller in the IPMC subsystem will configure the SPM external interfac

Release historyRelease Date Description-0000 December 2006 Initial releaseCopyright © 2006 by RadiSys Corporation. All rights reserved. RadiSys is a

Theory of Operation220On the ATCA-5000, the following signals to Jn4 are routed as 100-Ohm differential pairs from the Zone 3 connector to the PIM Jn4

Power22110/100/1000 Ethernet interfacesTwo 10/100/1000 Ethernet connections are routed from the 3x32 DIN shelf connector to the daughter card connecto

Theory of Operation222

23CONNECTORS3Face-plate connectorsTelco alarm interface connectorThe Telco Alarm Interface connector is a 15-pin male D-shell (DA-15P) connector with

Connectors324The mating terminal block accepts 28 through 20 AWG solid or stranded wires, stripped to expose an 8-mm length of conductor. The followin

Interior connectors325Interior connectorsFigure 9. Interior connectors3x32 DINconnector1x3 powerconnectorPIM sitePIM Jn0connectorPIM Jn4connectorDaugh

Connectors326Zone 3 connector (ATCA-5000 only)Connections between the ATCA-5000 and the ATCA-2100 occur across a female DIN 41612-type connector, loca

Shelf ground headers3273x32 shelf connectorConnections between the SPM and the system occur across a female DIN 41612 type connector. It is located ab

Connectors328PIM Jn0 connectorJn0 matches VITA 36 (custom assignment).Table 10. Jn0 PIM connector pin assignmentsPin Signal Pin Signal1 not connected

PIM interfaces329PIM Jn4 connectorJn4 matches VITA 36 (custom assignment) Table 11. Jn4 PIM connector pin assignmentsPin Signal Pin Signal1VITA[1] 2VI

3TABLE OF CONTENTSPreface ... 5Electro

Connectors330

4

5PREFACEThis manual describes the ATCA-5000 and ATCA-5100 shelf peripheral modules (SPMs) and assists engineers, technicians, and developers in using

6Preface

7PRODUCT DESCRIPTION1The ATCA-5000 and ATCA-5100 shelf peripheral modules (SPMs) provide an interface for ATCA shelf management to various shelf perip

Product Description18Figure 1. ConnectionsThe SPM provides a PMC I/O Module (PIM) interface that the SCM can use.A connector is provided that is desig

Features19Features IPMC subsystem based on a Renesas H8S/2168 microcontroller that provides an interface to the ATCA IPMB-0 bus Event inputs—four op