To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
IILIMITED WARRANTY Hitachi warrants its user system interface cables to be manufacturedin accordance with published specifications and free from d
IIIState Law: Some states do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so t
IVSAFETY PAGEREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for future ref
VWARNINGObserve the precautions listed below. Failure to do sowill result in a FIRE HAZARD and will damage the usersystem and the emulator product or
iPrefaceThank you for purchasing this user system interface cable (HS2282ECF61H) for the Hitachi’soriginal microcomputer H8S/2282 series.The HS2282ECF
iiContentsSection 1 Configuration...1Section 2 Connection Proced
1Section 1 ConfigurationCAUTIONUse an IC149-KS-11113-0 socket (manufactured byYAMAICHI ELECTRONICS Co., Ltd.) for the FP-100A packageIC socket on t
2Table 1 HS2282ECF61H ComponentsNo. Component Quantity Remarks1 Cable body 1 Flat cable2 Cable head 13 IC socket 1 For the FP-100A package4 Socket cov
3Section 2 Connection Procedures2.1 Connecting User System Interface Cable to Emulator StationWARNINGObserve the precautions listed below. Failure
4Figure 2 Connecting User System Interface Cable to Emulator Station
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
52.2 Connecting User System Interface Cable to User SystemWARNINGAlways switch OFF the user system and the emulatorproduct before the USER SYSTEM INTE
62.2.4 Fastening Cable HeadCAUTION1. Use a Phillips-type screwdriver whose head matchesthe screw head.2. The tightening torque must be 0.098 N•m or le
7Fasten the user system interface cable head to the IC socket for an FP-100A package on the usersystem with the two screws (M2.5 x 11 mm) provided. E
82.2.5 Fastening Cable BodyConnect the cable body to the cable head.Cable bodyCable headRemove jigPush the remove jig.User systemRemovingFigure 4 Fa
92.3 Recommended Dimensions for User System Mount PadFigure 5 shows the recommended dimensions for the mount pad (footprint) for the user systemwith a
102.4 Dimensions for User System Interface Cable HeadThe dimensions for the user system interface cable head are shown in figure 6.Figure 6 Dimensio
112.5 Resulting Dimensions after Connecting User System Interface CableThe resulting dimensions, after connecting the user system interface cable head
12Section 3 Installing the MCU to the User SystemCAUTION1. Check the location of pin 1 before inserting.2. If the MCU does not operate correctly, cr
13Section 4 Verifying Operation1. When using the E6000 emulator for the H8S/2636 and H8S/2646 series, turn on the emulatoraccording to the procedure
14Section 5 Setting TRPB2, TRPA2, TRPA1, and TRPB1SwitchesIn this user system interface cable, TRPB2, TRPA2, TRPA1, and TRPB1 switches control thetr
Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati
15Section 6 Notice1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cablehead before inserting the cable h
166. The P1 short connector is used for testing. Do not remove the inserted jumper pin.Figure 12 P1 Short Connector
Cautions Keep safety first in your circuit designs! 1. Renesas Technology Corporation puts the maximum effort into making semiconductor products bett
H8S/2282 Series FP-100AUser System Interface Cable(HS2282ECF61H) for E6000 EmulatorUser’s ManualUser’s Manual Rev.2.0 2002.02
Cautions1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’spatent, copyright, trademark, or other intellec
IIMPORTANT INFORMATIONREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for f
Kommentare zu diesen Handbüchern