Renesas H8S/2237 Series Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

i Preface Thank you for purchasing this user system interface cable (HS2238ECN61H) for the Renesas’s original microcomputer H8S/2237, H8S/2238R serie

ii Contents Section 1 Configuration...1 Section 2 Connection Pr

Section 1 Configuration 1 UTIONCA Use an NQPACK100SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-100G package IC socket on

2 Table 1 lists the HS2238ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2238ECN61H Components No.

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Always switch OFF the user system and the

2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USER S

2.2.1 Installing IC Socket 1. Confirming the location of IC socket 5 UTIONCA After confirming the location of pin 1 on the IC socket, apply

2.2.2 Inserting Cable Head 6 UTIONCA Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-100G package on the u

Fasten the user system interface cable head to the IC socket for a TFP-100G package on the user system with the four screws (M2 x 10 mm) provided. Ea

2.2.4 Connecting Cable Body to Cable Head Connect the cable body to the cable head. Cable bodyCable headRemove jigPush the remove jigRemovingUser sy

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with

2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. 45.748.64.04-φ2

2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head

Section 3 Installing the MCU to the User System 12 UTIONCA 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided fo

MCUPin 1IC socket (NQPACK100SEmanufactured by Tokyo Eletech Corporation)User systemScrews (M2 x 6 mm)Socket cover Figure 9 Installing MCU to User Sys

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 series, turn on the emulator according to the procedures described i

Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable h

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy

II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and free

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so

SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for future re

WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulato

H8S/2237, H8S/2238R Series TFP-100GUser System Interface Cable(HS2238ECN61H) for E6000 EmulatorUser’s ManualUser’s ManualRev.1.0 2003.04

Cautions 1. Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intel