Renesas Emulation Pod M3062NT3-RPD-E Technical Information

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

( 8 / 84 )MEMO

( 9 / 84 )Chapter 1. Precautions for SafetyThis chapter describes precautions for using this product safely and properly. For precautions for the emul

( 10 / 84 )Chapter 1. Precautions for SafetyIn both the user's manual and on the product itself, several icons are used to insure proper handling

( 11 / 84 )WARNINGWarning for Installation:• Do not set this product in water or areas of high humidity. Make sure that the main unit does notget wet.

( 12 / 84 )Notes on Downloading Firmware:• Before using this product for the first time, it is necessary to download the dedicated firmware.Please not

( 13 / 84 )IMPORTANTNote on Clock Supply to the MCU:• Clock can be supplied to the evaluation MCU in one of the following two ways. This is determined

( 14 / 84 )Notes on MAP References and Settings:• For details on referencing and setting MAP information, see the emulator debugger M3T-PD30user'

( 15 / 84 )IMPORTANTNote on Operation When Not Executing the User Program:• With this product, bit 7 of processor mode register 1 (wait bit PM17) is f

( 16 / 84 )IMPORTANTNotes on Software and Hardware Breaks:• The software break is a debugging function which breaks a program immediately before the s

( 17 / 84 )IMPORTANTNote on Reading Internal Resources of the MCU:• When the registers that are listed in Table 1.1 are read with an emulator, those r

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

( 18 / 84 )IMPORTANTNote on Differences Between the Actual MCU and Emulator:• Operation of the emulator differs from that of the actual MCU as listed

( 19 / 84 )IMPORTANTNote on Debugging Operations After Releasing a Reset from the Target:• Do not execute debugging operations such as setting a softw

( 20 / 84 )MEMO

( 21 / 84 )Chapter 2. PreparationThis chapter describes the package components, the system configuration and the preparation for using this product fo

( 22 / 84 )* Please keep the M3062NT3-RPD-E's packing box and cushion material in your place for reuseat a later time when sending your product f

( 23 / 84 )2.3 Name of Each Part(1) System ConfigurationFigure 2.1 System configuration(1) to (4) in Figure 2.1 are included with this product package

( 24 / 84 )(2) Inside of the Emulation PodFigure 2.2 Internal view of the emulation pod(1) MCU-dependent board 1This is a board for port emulation.(2)

( 25 / 84 )2.4 When Using This Product for the First Time(1) Making an MCU FileIt is necessary to make an MCU file to use this product with the emulat

( 26 / 84 )See "4.3 Self-check" (page 57).Within 2 seconds of turning the power ON, press thesystem reset switch of the PC4701 and check it

( 27 / 84 )Chapter 3. Setting UpThis chapter describes switch settings required for using this product and how to connect this product to the PC4701 a

M3062NT3-RPD-EUser’s ManualUser’s ManualRev.1.00 2003.06Emulation Pod for M16C/62 Group M16C/62N and M16C/30 Group M16C/30L

( 28 / 84 )Chapter 3. Setting UpTo use this emulation pod with your target system, it is necessary to set as follows. Set the followingafter removing

( 29 / 84 )3.2 Each SettingFigure 3.2 shows the positions of the following parts.(1) Oscillator circuit board(2) Switches(3) Pullup resistors(4) A-D c

( 30 / 84 )3.3 Selecting Clock Supply and Replacing Oscillator Circuit Boards(1) Clock Supply to the MCUThere are two ways to supply a clock to the MC

( 31 / 84 )(2) Using the Oscillator Circuit on the Target SystemTo operate this product with an external clock, construct the oscillator circuit as sh

( 32 / 84 )(3) Changing the Internal Oscillator Circuit of the Emulation PodAn oscillator circuit board for 16.0 MHz (OSC-3) is mounted on this produc

( 33 / 84 )(4) Replacing Oscillator Circuit BoardsFigure 3.7 shows how to replace the oscillator circuit boards. For the position of the oscillator ci

( 34 / 84 )3.4 Switch SettingsHere follows explanations of the switches of the M3062NT3-RPD-E.Tables 3.2 and 3.3 list how to set toggle switches SW1 t

( 35 / 84 )SW5SW5(Factory-setting)Table 3.3 Switch settings of the M3062NT3-RPD-E (2/3)Xout SW3SW4P86/XcoutSignal Switch Setting DescriptionDoes not c

( 36 / 84 )(2) Jumper Switches JP1 and JP2 on the M30620T3-PRT Board (MCU-dependent 1)Table 3.4 Switch settings of the M3062NT3-RPD-E (3/3)A18_SELJP1V

( 37 / 84 )Figure 3.8 Position for mounting pullup resistors3.5 Installing and Removing Pullup ResistorsIn this product, you cannot control pullup for

( 2 / 84 )* IC61-1004-051 is a trademark of Yamaichi Electronics Co., Ltd.* NQPACK, YQPACK, YQSOCKET, YQ-GUIDE, HQPACK, TQPACK and TQSOCKET are tradem

( 38 / 84 )Figure 3.9 Foot patterns of A-D conversion bypass capacitor3.6 A-D Conversion Bypass CapacitorsThe M3062NT3-RPD-E has the M3062PT3-PRTM boa

( 39 / 84 )3.7 Connecting the PC4701To connect the emulation pod to the PC4701, use the FLX120-RPD 120-pin flexible cable includedwith this product pa

( 40 / 84 )(2) Connecting the Cable to the Emulation PodFigure 3.11 shows how to connect the FLX120-RPD and the emulation pod.Figure 3.11 Connecting t

( 41 / 84 )3.8 Connecting the Target SystemThere are several ways available to connect the emulation pod to target systems as shown in Figure 3.12.CAU

( 42 / 84 )(1) Connecting to a 100-pin LCC SocketTo connect the M30800T-PTC (included) to the 100-pin LCC socket (IC61-1004-051 by YamaichiElectronics

( 43 / 84 )Figure 3.14 Connecting to an 80-pin 0.65-mm-pitch foot pattern (part 1)(2) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 1)Here

( 44 / 84 )Figure 3.15 Connecting to an 80-pin 0.65-mm-pitch foot pattern (part 2)(3) Connecting to an 80-pin 0.65-mm-pitch Foot Pattern (Part 2)Here

( 45 / 84 )(4) Connecting to a 100-pin 0.65-mm-pitch Foot Pattern (Part 1)Here follows how to connect the emulation pod probe to a 100-pin 0.65-mm-pit

( 46 / 84 )Figure 3.17 Connecting to a 100-pin 0.65-mm-pitch foot pattern (part 2)CAUTIONNotes on Connecting the Target System:• Take care not to atta

( 47 / 84 )Figure 3.18 Connecting to a 100-pin 0.65-mm-pitch foot pattern (part 3)CAUTIONNotes on Connecting the Target System:• Take care not to atta

( 3 / 84 )PrefaceThe M3062NT3-RPD-E is an emulation pod for the M16C/62 Group M16C/62N and M16C/30Group M16C/30L of 16-bit MCUs. It is used with a PC4

( 48 / 84 )Figure 3.19 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 1)CAUTIONNotes on Connecting the Target System:• Take care not to attac

( 49 / 84 )Figure 3.20 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 2)CAUTIONNotes on Connecting the Target System:• Take care not to attac

( 50 / 84 )Figure 3.21 Connecting to a 100-pin 0.5-mm-pitch foot pattern (part 3)CAUTIONNotes on Connecting the Target System:• Take care not to attac

( 51 / 84 )Figure 3.22 Connecting to a 100-pin 0.4-mm-pitch foot patternCAUTIONNotes on Connecting the Target System:• Take care not to attach the con

( 52 / 84 )MEMO

( 53 / 84 )Chapter 4. UsageThis chapter describes from turning on the power of this product to starting up the emulator debugger.4.1 Turning On the Po

( 54 / 84 )Chapter 4. Usage4.1 Turning On the Power(1) Checking Connections of the Emulator SystemBefore turning the power ON, check the connections o

( 55 / 84 )(3) LED Display When the PC4701 Starts Up NormallyAfter the emulator starts up, check the status of the LEDs on the front panel to see whet

( 56 / 84 )4.2 Downloading Firmware(1) When It is Necessary to Download FirmwareIt is necessary to download the firmware in the cases listed below. No

( 57 / 84 )4.3 Self-check(1) Self-check ProcedureTo run the self-check of the emulator, do so as explained here below. While the self-check is inprogr

( 4 / 84 )ContentsChapter 1. Precautions for Safety ...

( 58 / 84 )Figure 4.4 Self-check procedure

( 59 / 84 )Chapter 5. SpecificationsThis chapter describes specifications of this product.5.1 Specifications ...

( 60 / 84 )Chapter 5. Specifications5.1 SpecificationsTable 5.1 lists the specifications of the M3062NT3-RPD-E.Table 5.1 Specifications of the M3062NT

( 61 / 84 )5.2 Operation Timing in Memory Expansion and Microprocessor Modes(1) Separate Bus, No-WaitTable 5.2 and Figure 5.1 show the bus timing in m

( 62 / 84 )ReadWriteFigure 5.1 Memory expansion and microprocessor modes (no-wait)Conditions:• VCC = 3.3 V• Input timing voltage: VIL = 0.52 V, VIH =

( 63 / 84 )(2) Separate Bus, With Wait, Accessing External Memory AreaTable 5.3 and Figure 5.2 show the bus timing in memory expansion and microproces

( 64 / 84 )Figure 5.2 Memory expansion and microprocessor modes (with wait, accessing external area)ReadWriteConditions:• VCC = 3.3 V• Input timing vo

( 65 / 84 )(3) Multiplex Bus TimingTable 5.4 and Figure 5.3 show the bus timing in memory expansion and microprocessor modes (withwait, accessing exte

( 66 / 84 )Figure 5.3 Memory expansion and microprocessor modes (with wait, accessing external area, using multiplex bus)ReadWriteConditions:• VCC = 3

( 67 / 84 )Figure 5.4 Timing requirements(4) Timing RequirementsTable 5.5 and Figure 5.4 show the timing requirements.Table 5.5 Timing requirementsCom

( 5 / 84 )2.3 Name of Each Part ... 23(1) System

( 68 / 84 )Figure 5.5 Connection diagram5.3 Connection DiagramFigure 5.5 shows a connection diagram of the M3062NT3-RPD-E. This connection diagram mai

( 69 / 84 )Table 5.6 Electrical characteristics of the 74HC4066Table 5.7 Electrical characteristics of the FPGASymbol ItemStandard valuesStandardMax.M

( 70 / 84 )Figure 5.6 External dimensions of the emulation pod5.4 External Dimensions(1) External Dimensions of the Emulation PodFigure 5.6 shows exte

( 71 / 84 )Figure 5.7 External dimensions of the converter board M30800T-PTC and a sample foot patternUnit: mm(2) External Dimensions of the Converter

( 72 / 84 )Figure 5.9 External dimensions and a sample foot pattern of the converter board M3T-F160-100NSEUnit: mm(3) External Dimensions of the Conve

( 73 / 84 )Chapter 6. TroubleshootingThis chapter describes how to troubleshoot when this product does not work properly.6.1 Flowchart to Remedy the T

( 74 / 84 )Chapter 6. Troubleshooting6.1 Flowchart to Remedy the TroublesFigure 6.1 shows the flowchart to remedy troubles from when power to the emul

( 75 / 84 )6.2 When the Emulator Debugger Does Not Start Up Properly(1) When the LED Display of the PC4701 is AbnormalTable 6.1 LED's abnormal di

( 76 / 84 )(2) Program Window is Not Displayed at Debugger Startup (Target Connected)Table 6.2 Checkpoints of errors when starting up the emulator deb

( 77 / 84 )(3) Program Window is Not Displayed at Debugger Startup (Target Not Connected)Table 6.3 Checkpoints of errors when starting up the emulator

( 6 / 84 )4.3 Self-check... 57(1)

( 78 / 84 )MEMO

( 79 / 84 )Chapter 7. Maintenance and GuaranteeThis chapter describes how to maintenance, repair provisions and how to request for repair.7.1 Maintena

( 80 / 84 )Chapter 7. Maintenance and Guarantee7.1 MaintenanceIf dust or dirt collects on any equipment of your emulation system, wipe it off with a d

( 81 / 84 )7.4 How to Request for RepairIf your product is found faulty, follow the procedure below to send your product for repair.Customer Fill in t

MEMO

M3062NT3-RPD-E User's ManualRev. 1.00June 16, 2003REJ10J0113-0100ZCOPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATIONAND RENESAS SOLUTIONS CORPORATION

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanM3062NT3-RPD-EREJ10J0113-0100ZUser’s Manual

( 7 / 84 )TerminologySome specific words used in this user's manual are defined as follows:Emulator systemThis means an emulator system built aro