Renesas SH7201 Bedienungsanleitung

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

Chapter 5. Block Diagram Figure 5-5-1 shows the CPU board components and their connectivity. MicrocontrollerUser: 4 LEDS1Green, 1Orange, 2RedAppl

Chapter 6. User Circuitry 6.1. Switches There are four switches located on the CPU board. The function of each switch and its connection are shown i

6.4. Serial port The microcontroller programming serial port (SCIF5) is connected to the E8 connector. This serial port can optionally be connected t

6.6. Option Links Table 6-5 below describes the function of the option links contained on this CPU board. The default configuration is indicated by B

R32 Motor Connects microcontroller pin 170 to UD Disconnects microcontroller pin 170 from UD R31 R33 Write Signal Connects microcontroller pin 72

R71 Serial port Connects serial port PTTX to RS232 Serial Disconnects serial port PTTX from RS232 Serial R60, R66, R90 R72 Power supply Connects V

R123 CAN transceiver 0 Connects CAN0_STBn to microcontroller pin 166 Disconnects CAN0_STBn from microcontroller pin 166 - R124 CAN transceiver 0 Co

Chapter 7. Programming Methods The board is intended for use with HEW and the supplied E10A debugger only. Please refer to the datasheet of the Flas

Chapter 8.Headers 8.1. Microcontroller Headers Table 8-1 to show theTable 8-4 microcontroller pin headers and their corresponding microcontroller

J2 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 GND - 23 SDCKE 67 2 DREQ3 46 24 LED1 68 3 DACK3 47 25 DLCDE 69 4 DACT3

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 AN3 89 23 TxD1 111 2 AN4 90 24 SCK0 112 3 AN5 91 25 RxD0 113 4 AN6_DA

J4 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 ASEMDn 133 23 GND - 2 MD1 134 24 TIOC3A 154 3 MD0 135 25 UC_VCC - 4 W

8.2.Application Headers Table 8-5 and belowTable 8-6 show the standard application header connections. Note: Asterisk indications apply to all tab

JA2 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 RESn RESn 2 14 Un Un 160 2 EXTAL C

JA3 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 BA(0) BA(0) - 26 BWRn BWRn - 2 BA(1

JA5 Pin Header Name CPU board Signal Name Device Pin Pin Header Name CPU board Signal Name Device Pin 1 AD4 AN4 90 13 Reserved 2 AD5 AN5

Chapter 9. Code Development 9.1. Overview Note: For all code debugging using Renesas software tools, the CPU board must be connected to a PC USB por

Chapter 10. Component Placement Figure 11-1: Component Placement (Top Layer)23

Figure 11-2: Component Placement (Bottom Layer) 24

Chapter 11. Additional Information For details on how to use High-performance Embedded Workshop (HEW), refer to the HEW manual available on the CD o

Renesas Starter Kit for SH7201User’s ManualUser’s ManualRev.2.00 2008.03RENESAS SINGLE-CHIP MICROCOMPUTERSuperH™RISC engine

Renesas Starter Kit for SH7201 User's Manual Publication Date Rev.2.00 11.Mar.2008 Published by: Renesas Techn

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for SH7201REG10J0121-0200User’s Manual

Table of Contents Chapter 1. Preface...

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. No one is permitted t

Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. Features include: • Renesas Microcontroller Programming. • User C

Chapter 3. Power Supply 3.1. Requirements This CPU board operates from a 5V power supply. A diode provides reverse polarity protection only if a cur

Chapter 4. Board Layout 4.1. Component Layout The following diagram shows top layer component layout of the board. Figure 4-1: Board Layout 4

4.2.Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid