Renesas R8C/15 Bedienungsanleitung

REJ10J0746-0110 RENESAS SINGLE-CHIP MICROCOMPUTER M16C FAMILY / R8C/Tiny SERIES Rev.1.10 Renesas Solutions Corp.Revi

10 2.2 Emulator Software, C Compiler and High-performance Embedded Workshop Installations 1) Installation Double-click an installer of CD-ROM ¥

11 Only when you agree with License Agreement, click "Yes". Select all and click “Next” Refer to a new folder name, or select from

12 Refer to a new folder name, or select from the existing folder list and click “Next”. Click “Yes” Check the setting before starting the i

13 Check the setting before starting the installation and if the setting is correct, click “Next”. Then, a copy will be started. Click “Finish

14 2.3 USB driver installation Connect the E8 emulator using the USB cable to the USB port of host machine. <Windows XP> Installation pr

15 Renesas USB drivers are not authenticated by Microsoft, but we provide them based on the sufficient examination. Insert CD-ROM and specify ¥

16 <Windows 98/ME> Installation procedures are described below. If E8 emulator is connected, it is recognized as a new hardware. Click “Nex

17 Click “Next”. Click “Finish”. The installation is completed above.

18 2.4 Operate Sample Program 1) Copy ¥Japanese¥M3A0115_17¥PROGRAM¥ in CD-ROM to the given folder. 2) Change a file attribute Since the copied fi

19 Click “OK”. The installation is completed above.

1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corporation product best sui

20 <Windows 98/ME> Select all files in the copied folder by a mouse. Select “File” and “Property”. Remove a check of “Read-only” and cl

21 Click “Close”. Perform this setting to files in all folders of “3min_timer” and “ad_onkai”. The installation is completed above.

22 3) Connect a target board Use a user cable to the E8 emulator and connect a target board. Perform the below setting for the jumper setting o

23 4) Compile a sample program The example of the musical scale program (ad_onkai.hws) is shown below. (1) Start High-performance Embedded Worksh

24 (4) Select “R5F21174” for Device and put a check into “Download emulator firmware” for Mode. Click “OK”. (5) When 5V power supply is perform

25 (3) Execute Click “Debug” - “Execute”. (4) If clicking “Debug” - “Stop a program”, a program will stop. When executing the program again, cli

REVISION HISTORY Description Rev. Date Page Summary 0.10 2004.08.18 - First edition issued 1.00 2005.02.01 - It changed from FDTlight to fla

R8C/15, R8C/17 StarterKit Tutorial Publication Date Rev.1.10 Mar 01, 2005 Published by: Renesas Solutions Corp. 4-1-6

Renesas Solutions Corp. 4-1-6, Miyahara, Yodogawa-ku, Osaka City, 532-0003, Japan R8C/15, R8C/17 StarterKitTut

3 Table of Contents 1.accessory softwares to install 2.Until a sample program is operated with an emulator software P4 2.1 Flash programmer (F

4 1. accessory softwares to install 1) Note the following points before installing. a) The M3T-NC8C has already been installed. b) The M3T-NC3

5 Click “OK”. Click “Next” Select language to be used and click "Next"

6 Only when you agree with License Agreement, click "Yes". Click “Next”. Click “Next”.

7 Remove a check. Click “Next” Click “Next”. Refer to a new folder name, or select from the existing folder list and Click “Next”.

8 Refer to a new folder name, or select from the existing folder list and Click “Next”. Click “Next”. Click “Install”.

9 Click “finish”.