To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul
Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other inte
i Preface Thank you for purchasing this user system interface cable (HS2138ECH61H) for the Hitachi’s original microcomputer H8S/2138 series. The HS21
ii Contents Section 1 Configuration...1 Section 2 Connection P
1 Section 1 Configuration CAUTION Use an IC149-080-017-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the FP-80A package
2 Figure 1 HS2138ECH61H User System Interface Cable
3 Table 1 lists the HS2138ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2138ECH61H Components No.
4 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.
5 Emulator stationE6000Cable bodyUser system interface cable Figure 2 Connecting User System Interface Cable to Emulator Station
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
6 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE
7 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-80A package on the us
8 Fasten the user system interface cable head to the IC socket for an FP-80A package on the user system with the four screws (M2 x 12 mm; with four f
9 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigPush the remove jigRemovingUser system Figure 4
10 2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system
11 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6
12 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdrive
14 MCUPin 1IC socket (IC149-080-017-B5manufactured by YAMAICHI ELECTRONICS Co., Ltd.)User systemScrews (M2 x 8 mm) with flat washersSocket cover Figu
15 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User's Manual
Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati
16 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca
H8S/2138 Series QFP-80AUser System Interface Cable(HS2138ECH61H) for E6000 EmulatorUser’s ManualUser’s ManualRev.0.1 2000.09
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy
II LIMITED WARRANTY Hitachi warrants its user system interface cables to be manufactured in accordance with published specifications and free
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so
IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur
Kommentare zu diesen Handbüchern