Revision Date: Jun. 22, 2005 Renesas Microcomputer Development Environment System H8 Family / H8/300H Tiny Series HS36902ECH61HE Rev.1.00 H
VI
i Preface Thank you for purchasing this user system interface cable (HS36902ECH61H) for the Renesas’ original microcomputer H8/36912, H8/36902 group.
ii Contents Section 1 Configuration...1 Section 2 Connection Pr
1 Section 1 Configuration CAUTION Use an NQPACK032SA socket (manufactured by Tokyo Eletech Corporation) for the FP-32A package IC socket
2 Table 1 lists the HS36902ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS36902ECH61H Components No
3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.
4 E6000Emulator stationUser system interface cableCTS screws (M3 x 6 mm)Cable body connector Figure 2 Connecting User System Interface Cable to Emu
5 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE
6 2.2.1 Installing IC Socket After checking the location of pin 1 on the IC socket fasten it to the user system before soldering. CAUTION After
7 CAUTION Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly mor
8 Fasten the user system interface cable head to the IC socket for an FP-32A package on the user system with the two screws (M2 x 10 mm) provided. E
9 2.2.4 Fastening Cable Body Connect the cable body to the cable head. Cable headRemove jigUser systemPush the unfastening jigs.RemovingCable body F
10 2.3 Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system
11 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Uni
12 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable
13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided f
14 MCUPin 1IC socket (NQPACK032SAmanufactured by Tokyo Eleteck Corporation)User systemScrews (M2 x 6 mm)Socket cover Figure 9 Installing MCU to Use
15 Section 4 Verifying Operation 1. Turn on the emulator according to the procedures described in the H8/3664 E6000 Emulator User’s Manual (HS3664
16 Figure 10 shows the system clock oscillator on the user system interface cable and the subclock input specifications. R2 270 ΩR1 1 MΩHCU04HCU04To
17 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the cu
18 6. The P1 short connector is used for testing. Do not remove the inserted jumper pin. P113 Figure 12 P1 Short Connector
19 7. SW1 and SW2 are used to switch OSC2 or PC1 and OSC1 or PC0. Turn SW1 and SW2 to the OSC1 and OSC2 sides, respectively, when they are used as O
20
Renesas Microcomputer Development Environment System User's Manual H8/36912, H8/36902 Group FP-32AUser System Inte
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japanhttp://www.renesas.comRef
H8/36912, H8/36902 Group FP-32A User System Interface Cable HS36902ECH61H User’s Manual
I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy
II LIMITED WARRANTY Renesas warrants its user system interface cables to be manufactured in accordance with published specifications and f
III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages,
IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur
V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul
Kommentare zu diesen Handbüchern