Renesas V850E2 Bedienungsanleitung Seite 1

_ V9.12. 184 Technical Notes Renesas V850E2/Fx4 Family In-Circuit Emulation  iSYSTEM, September 2014 1/23 This document is intende

 iSYSTEM, September 2014 10/23 4 Flash Mask Options and Security Flags The dialog under the Hardware/Tools/FLASH menu provide access to the V850E

 iSYSTEM, September 2014 11/23 5 Memory Access V850E2 debug interface features a real-time memory access, that does not require user program to

 iSYSTEM, September 2014 12/23 7 OSEK Debug Support Enable OSEK support by selecting ‘ORTI (AUTOSAR,OSEK,CMX)’ selection in the ‘Debug/Operating

 iSYSTEM, September 2014 13/23 9 Trace The V850E2/Fx4 development system is based on a Renesas Fx4 Umbrella device that incorporates an On-Chip

 iSYSTEM, September 2014 14/23 Trace Qualifier The Watchpoint Trace width and Data Message Type are shown in their default, recommen

 iSYSTEM, September 2014 15/23 9.3 Trace Examples Analyzer window is opened from the View menu. Before using trace for the first time please ref

 iSYSTEM, September 2014 16/23 Before the program is set to run or while it is running already, activate the trace recording by the ‘Trace begin

 iSYSTEM, September 2014 17/23 Example 2 Trigger Settings Now activate the trace and run the program. When the trigger event occurs,

 iSYSTEM, September 2014 18/23 Example 2 Trace Result When the trigger occurs, trace port outputs a special trigger message called Wa

 iSYSTEM, September 2014 19/23 Example 3: The trace will start recording (instructions and data accesses) after the function Type_Sim

 iSYSTEM, September 2014 2/23 1 Introduction The Renesas V850E2/Fx4 ActiveGT POD is built from the iC3000/ActiveGT platform from iSYSTEM and a sp

 iSYSTEM, September 2014 20/23 Example 3 Qualifier Settings Start the trace and run the application from reset on. After Type_Simple() is execute

 iSYSTEM, September 2014 21/23 Example 3 Trace Result The first one is to use the non-real-time trace mode, which stalls the CPU un

 iSYSTEM, September 2014 22/23 Example 4: Configure trace to record only data accesses to the 32-bit global variable named iCounter. Following pi

 iSYSTEM, September 2014 23/23 Example 4 Trace Result 10 Coverage Refer to winIDEA Contents Help, Coverage Concepts section for Coverage theory a

 iSYSTEM, September 2014 3/23 2 Emulation Options 2.1 Hardware Options In-Circuit Emulator Options dialog, Hardware page There are no user sett

 iSYSTEM, September 2014 4/23 In-Circuit Emulator Options dialog, Vcc/Clock Setup page No option here, as well. The POD power is provided so tha

 iSYSTEM, September 2014 5/23 2.5 JTAG Scan Speed JTAG Scan Speed definition Scan speed JTAG Scan Speed is automatically set to the Free mode. T

 iSYSTEM, September 2014 6/23 3 CPU Setup 3.1 CPU Options The CPU Setup, Options page provides some emulation settings, common to most CPU famil

 iSYSTEM, September 2014 7/23 3.2 Debugging Options This pane exposes two options related to a memory access. Displayed below are default setting

 iSYSTEM, September 2014 8/23 3.3 Reset Options Latch target RESET When the option is checked, the debugger latches active target reset

 iSYSTEM, September 2014 9/23 The trace clock frequency can be checked in the Plugins/Measurement window. The Trace Clock is measured on